manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 106

Fold-away mirrors

Fold the side mirrors in carefully
before driving through a narrow
space, like an automatic car wash.

Power-folding mirrors (if
equipped)

With power-folding mirrors, you can
fold the side mirrors using the
power mirror switch.

1. Rotate the switch to the
center/neutral position.

2. Momentarily pull the switch
rearward to auto fold in.

3. Momentarily pull the switch rearward again to fold back to design
position.

The power-folding mirrors may be moved inward/outward manually.
However, if a mirror is moved manually, it will need to be reset. A mirror
which has not been reset may appear to be loose. To reset: with the
switch in the center position, momentarily pull the switch rearward to
fold the mirrors in. An audible

⬙

click

⬙

will be heard indicating

re-synchronization. If the click is not heard, use the switch to fold the
mirrors out, then in, until the click is heard. After that, the mirrors will
operate normally until they are again moved manually.

Note:

10 or more switch activations within one minute, or repeated

folding/unfolding of the mirrors while holding the switch rearward during
full travel, may cause the system to disable the fold/unfold function to
protect motors from overheating. Should this occur, wait approximately
three minutes with the vehicle running and up to 10 minutes with the
vehicle off, for the system to reset and for function to return to normal.

Heated outside mirrors (if equipped)

Heated mirrors remove ice, mist and
fog. To activate the heated mirrors,
press the rear defrost button

R

located on the climate control panel.

Refer to

Rear window defroster

in

the

Climate Controls

chapter for

more information.

Driver Controls

106

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands