Ford 2012 F-150 Owner'S Manual Download Page 45 | Manualshive

Page: 45 / 476

Ford 2012 F-150 Owner'S Manual Download Page 45

TRAILER BRAKE MODULE FAULT (if equipped)

— Displayed and

accompanied by a single chime, in response to faults sensed by the TBC.
Refer to

Trailer towing

in the

Tires, Wheels and Loading

chapter for

more information.

TRAILER CONNECTED (if equipped)

— Displayed when a correct

trailer connection (a trailer with electric trailer brakes) is sensed during
a given ignition cycle. Refer to

Trailer towing

in the

Tires, Wheels and

Loading

chapter for more information.

TRAILER DISCONNECTED (if equipped)

— Displayed when a

trailer connection becomes disconnected, either intentionally or
unintentionally, and has been sensed during a given ignition cycle.
Disregard this status if your vehicle is not equipped with a factory
installed trailer brake controller. This message may appear when an
aftermarket TBC is used even when the trailer is connected. Refer to

Trailer towing

in the

Tires, Wheels and Loading

chapter for more

information.

TRAILER SWAY REDUCE SPEED (if equipped)

— Displayed when

the trailer sway control has detected trailer sway. For more information,
refer to the

Driving

chapter for more information.

WIRING FAULT ON TRAILER (if equipped)

— Displayed if there

are certain faults in the vehicle wiring and trailer wiring/brake system.
Refer to

Trailer towing

in the

Tires, Wheels and Loading

chapter for

more information.

FOR OFF ROAD SLOW TO 5 MPH (if equipped)

— Displayed when

the vehicle speed requirement for off-road mode entry has not been met.

OFF ROAD MODE ENABLED (if equipped)

— Displayed when

off-road mode becomes active.

EXITING OFF ROAD MODE (if equipped)

— Displayed when

off-road mode becomes inactive.

HILL DESCENT CONTROL ACTIVE (if equipped)

— Displayed

when hill descent control mode becomes active.

HILL DESCENT CONTROL OFF (if equipped)

— Displayed when hill

descent control mode becomes inactive.

DRIVER RESUME CONTROL (if equipped)

— Displayed when the

hill control and off-road mode require the driver to resume control.

COAST DOWN MODE (if equipped)

— Displayed when vehicle enters

coast down mode.

FOR HILL DESCENT REDUCE SPEED (if equipped)

— Displayed

when the vehicle speed requirement for off-road mode entry has not
been met.

Instrument Cluster

45

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

«
...
43
44
45
46
47
...
»

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands