Ford 2012 F-150 Owner'S Manual Download Page 37

Page: 37 / 476

Vehicle*

Oil Life Reset

Set to XXX% (Press and hold OK to set).

Pwr Running
Boards

Auto/Off/Out

Remote Start

Climate Control

Front Defrost

Auto/Off

Rear Defrost

Driver Seat

Passenger Seat

Heater-A/C

Auto/ Last
Setting

Duration

5, 10 or 15 minutes, Off

Quiet Start

On/Off

Wipers

Courtesy Wipe

On/Off

Rain Sensing
wipers

On/Off

* If equipped—your vehicle may be equipped with some or all of these
options.

MyKey

Create MyKey

Hold OK to create MyKey

*AdvanceTrac

Always on or Selectable

*MAX Speed

80 MPH (120 km/h) or Off

*Speed Warning

45, 55 or 65 MPH (75, 90 or 105 km/h), Off

*Volume Limiter

On/Off

*Clear MyKeys

Hold OK to Clear MyKeys

*Only displays if MyKey is programmed.

Language

English, Español, Français

Units

Units

English or Metric

System Reset

Hold OK to Reset System to Factory Default

Instrument Cluster

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands

Ford 2012 F-150, Owner'S Manual

Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands