manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 119

For questions or comments, contact HomeLink

威

at www.homelink.com or

1-800-355-3515.

Programming HomeLink

姞

to a Genie Intellicode

姞

2 garage door

opener

Note:

The Genie Intellicode 2

威

transmitter must already be programmed

to operate with the garage door opener.

Programing the transmitters

To program HomeLink

威

to the transmitter you must first put the

transmitter into programming mode. To do this

A. Red LED

B. Green LED

1. Press and hold one of the buttons on the transmitter for 10 seconds.
The LED light will change from green to green and red.

2. Press the same button twice to confirm the change to Programming
mode. If done properly the LED light will appear red.

3. Hold the transmitter within 1–3 inches (2–8 cm) of the HomeLink

威

button.

4. Press and hold the both the programmed Genie button and the
HomeLink

威

button you want to program. The HomeLink

威

LED will flash

rapidly when the programming is successful.

Note:

the Genie transmitter will transmit for up to 30 seconds. If

HomeLink

威

does not program within 30 seconds the Genie transmitter

will need to be pressed again. If the Genie transmitter LED displays
green and red, release the button until the LED turns off before pressing
the button again.

B

A

Driver Controls

119

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands