manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 22

TBC GAIN (if equipped)

Displays the level of trailer brake gain or if the trailer is not connected.

System check and vehicle feature customization

Press the SETUP button repeatedly
to cycle the message center through
the following features:

RESET FOR SYSTEM CHECK

When this message appears, press
the RESET button and the message
center will begin to cycle through
the following systems and provide a
status of the item if needed.

Note:

Some systems show a message only if a condition is present.

1. XXX% OIL LIFE

2. DOOR STATUS

3. BRAKE SYSTEM

4. FUEL LEVEL LOW

5. TBC GAIN = XX.X
NO TRAILER (if equipped and no trailer connected)

6. TBC GAIN = XX.X
OUTPUT = ////// (if equipped and trailer connected)

7. MYKEY DISTANCE (if programmed)
8. MYKEY(S) PROGRAMMED
9. ADMIN KEYS PROGRAMMED

SETUP

RESET

INFO

SET

RSM

CNCL

RESET

INFO

SETUP

ON

OFF

SETUP

RESET

INFO

SET

RESET

INFO

SETUP

ON

OFF

RSM

CNCL

Instrument Cluster

22

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands