manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 420

AIR FILTER

Refer to

scheduled maintenance information

for the appropriate

intervals for changing the air filter element.

When changing the air filter element, use only the air filter element
listed. Refer to

Motorcraft

威

part numbers

in this chapter.

WARNING:

To reduce the risk of vehicle damage and/or

personal burn injuries do not start your engine with the air

cleaner removed and do not remove it while the engine is running.

Changing the air filter element (3.7L/5.0L and 6.2L engines)

1. Locate the mass air flow sensor
electrical connector on the air outlet
tube. This connector will need to be
unplugged.

2. Reposition the locking clip on the
connector (connector shown from
below for clarity), squeeze the
connector and pull it off of the air
outlet tube.

Maintenance and Specifications

420

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands