manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 180

1. Pull control to release seat
cushion.

2. Rotate seat cushion up until it
locks into vertical storage position.

Returning the seat to seating position

WARNING:

Make sure that cargo or any objects are not trapped

underneath the seat cushion before returning the seat cushion to

its original position, and that the seat cushion locks into place. Failure
to do so may prevent the seat from operating properly in the event of
a crash, which could increase the risk of serious injury.

1. Pull control on the side of the seat to release seat cushion from
storage position.

2. Push seat cushion down until it locks into horizontal position.

Folding Up the Rear Seats (SuperCrew Vehicles Only)

The rear seat has a split 60/40 cushion. Each seat cushion can be flipped
up into a vertical storage position.

•

Rotate the seat cushion up by
lifting on the corner until it locks
into vertical storage position.

Note:

The handle on the bottom of the seat cushion does not need to be

pulled to lift the seat cushion to the storage position.

Seating and Safety Restraints

180

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands