manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 66

NAVIGATION SYSTEM (IF EQUIPPED)

Your vehicle may be equipped with a navigation system. Refer to the

Navigation System

supplement for further information.

Battery management:

When the engine is off, your Navigation system

may turn off if the battery is at a low state of charge or if the ignition
has been in the accessory position or in the on position for
approximately 45 minutes. The display will temporarily show BATTERY
SAVER — SYSTEM OFF PLEASE START THE ENGINE and the
Navigation system will be turned off. The Navigation system will return
to normal operation once the vehicle has been started and battery state
of charge allowed to recover. The battery state of charge recovery can be
accelerated by turning off any unnecessary electrical loads while driving.
Refer to the

Battery management system

section in the

Maintenance

and Specifications

chapter for more information.

SYNC

姞

(IF EQUIPPED)

Your vehicle may be equipped with SYNC

威

, a hands-free communications

and entertainment system with special phone and media features. For
more information, please refer to the

SYNC

威

supplement or to the

SYNC

威

section in the

Navigation System

supplement (if equipped).

Entertainment Systems

66

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands