manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 140

KEYS

Your vehicle may be equipped with
two integrated keyhead transmitters
(IKTs). The key blade functions as a
programmed key which starts the
vehicle and unlocks/locks all the
doors. The transmitter portion
functions as the remote entry
transmitter.

Your IKTs are programmed to your vehicle; using a non-programmed key
will not permit your vehicle to start. If you lose your authorized dealer
supplied IKTs, replacement IKTs are available through your authorized
dealer. Standard SecuriLock

威

keys without remote entry transmitter

functionality can also be purchased from your authorized dealer if
desired.

Always carry a spare key with you in case of an emergency.

For more information regarding programming replacement IKTs, refer to
the

SecuriLock

威

passive anti-theft system

section later in this chapter.

Note:

Your vehicle’s IKTs were

issued with a security tag that
provides important vehicle key cut
information. It is recommended that
you keep the tag in a safe place for
future reference.

MYKEY

姞

(IF EQUIPPED)

The MyKey

威

feature allows you to program a restricted driving mode to

promote good driving habits. All but one of the keys programmed to the
vehicle can be activated as a MyKey

威

. The key will remain restricted

until MyKey

威

is cleared. Any remaining keys are referred to as an

“administrator key” or admin key. The admin key can be used to create a
MyKey

威

, program optional MyKey

威

settings, and clear the MyKey

威

feature. When the MyKey

威

feature is enabled the user can use the

system check in the message center to see how many MyKeys™ and
admin keys are programmed to the vehicle, and how many total miles
have been driven with the MyKey

威

active.

Locks and Security

140

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands