Ford 2012 F-150 Owner'S Manual Download Page 457

Page: 457 / 476

Every 15,000 miles
(24,000 km)

Replace cabin air filter (if equipped)

Every 30,000 miles
(48,000 km)

Replace climate-controlled seat filter (if
equipped)

Replace engine air filter

Every 97,500 miles
(156,000 km)

Replace spark plugs

Every 105,000 miles
(168,000 km)

Change engine coolant

Inspect accessory drive belt(s)

Every 150,000 miles
(240,000 km)

Change automatic transmission fluid and filter

Change front axle fluid (4WD vehicles)

Change rear axle fluid (RWD vehicles)

Change transfer case fluid (4WD vehicles)

Replace accessory drive belt(s) if not replaced
within the last 100,000 miles (160,000 km)

Initial replacement at 105,000 miles (168,000 km) or 72 months; every

45,000 miles (72,000 km) or 36 months thereafter

Perform a follow-up inspection at 120,000 miles (192,000 km)

Scheduled Maintenance

457

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands

Ford 2012 F-150, Owner'S Manual

Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands