Ford 2012 F-150 Owner'S Manual Download Page 30

Page: 30 / 476

KEY COULD NOT PROGRAM

— Displayed when an attempt is made

to program a spare key using two existing MyKeys. Refer to

MyKey

威

the

Locks and Security

chapter for more information.

CHECK LOCKING DIFFERENTIAL (if equipped)

— Displayed

when an electronic locking differential (ELD) system fault is present. For
more information, refer to

Electronic locking differential (ELD)

in the

Driving

chapter.

ELD ENGAGED/DISENGAGED (if equipped)

— Displayed when the

electronic locking differential (ELD) is enabled or disabled. For more
information, refer to

Electronic locking differential (ELD)

in the

Driving

chapter.

TO ENGAGE ELD SLOW TO XX MPH/KM/H (if equipped)

—

Displayed when the electronic locking differential requests a certain
speed requirement to engage. For more information, refer to

Electronic

locking differential (ELD)

in the

Driving

chapter.

TO ENGAGE ELD RELEASE PEDAL (if equipped)

— Displayed

when the electronic locking differential request the accelerator to be
released in order to engage. For more information, refer to

Electronic

locking differential (ELD)

in the

Driving

chapter.

HILL DESCENT CONTROL FAULT (if equipped)

— Displayed when

a hill descent system fault is present.

HILL CNTRL OFF SYSTEM COOLING (if equipped)

— Displayed

when a hill descent system fault is present.

FOR OFF ROAD SLOW TO 5 MPH (if equipped)

— Displayed when

the vehicle speed requirement for off-road mode entry has not been met.

OFF ROAD MODE ENABLED (if equipped)

— Displayed when

off-road mode becomes active.

EXITING OFF ROAD MODE (if equipped)

— Displayed when

off-road mode becomes inactive.

HILL DESCENT CONTROL ACTIVE (if equipped)

— Displayed

when hill descent control mode becomes active.

HILL DESCENT CONTROL OFF (if equipped)

— Displayed when

hill descent control mode becomes inactive.

FOR HILL CNTRL 20 MPH OR LESS (if equipped)

— Displayed

when the vehicle speed requirement for hill control mode entry has not
been met.

DRIVER RESUME CONTROL (if equipped)

— Displayed when the

hill control and off-road mode require the driver to resume control.

Instrument Cluster

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands

Ford 2012 F-150, Owner'S Manual

Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands