manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 257

Understanding your tire pressure monitoring system (TPMS)

The tire pressure monitoring system measures pressure in your four road
tires and sends the tire pressure readings to your vehicle. The low tire
pressure warning light will turn on if the tire pressure is significantly low.
Once the light is illuminated, your tires are under-inflated and need to be
inflated to the manufacturer’s recommended tire pressure. Even if the
light turns on and a short time later turns off, your tire pressure still
needs to be checked. Visit www.checkmytires.org for additional
information.

When your temporary spare tire is installed

When one of your road tires needs to be replaced with the temporary
spare, the TPMS will continue to identify an issue to remind you that the
damaged road wheel/tire needs to be repaired and put back on your
vehicle.

To restore the full functionality of the tire pressure monitoring system,
have the damaged road wheel/tire repaired and remounted on your
vehicle. For additional information, refer to

Changing tires with a

TPMS

in this section.

Tires, Wheels and Loading

257

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands