manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 49

Setting the clock:

Press and hold CLK until the hours begin to flash.

Press

/

/

SEEK

to manually increase/decrease the hours.

Press CLK again to set the minutes using

/

/

SEEK

to

manually increase/decrease the minutes. Allow 10 seconds to pass to
confirm that the time has been set.

Note:

If your vehicle is equipped with a navigation system, refer to

Setting the clock

in your

Navigation supplement

.

AM/FM in-dash CD/MP3 satellite compatible sound system

WARNING:

Driving while distracted can result in loss of vehicle

control, accident and injury. Ford strongly recommends that

drivers use extreme caution when using any device or feature that may
take their focus off the road. Your primary responsibility is the safe
operation of the vehicle. We recommend against the use of any
handheld device while driving, encourage the use of voice-operated
systems when possible and that you become aware of applicable state
and local laws that may affect use of electronic devices while driving.

Accessory delay:

Your vehicle is equipped with accessory delay. With

this feature, the radio and other electrical accessories may be used for
up to ten minutes after the ignition is turned off or until either front
door is opened.

OK

TUNE

LOAD

VOL

CD

AUX

AM/FM

SIRIUS

• DIRECT

TEXT

SCAN

CAT/FOLD

CLOCK #

SOUND

MENU

SEEK

1

2

3

4

5

6

7

8

9

0

Entertainment Systems

49

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands