manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 209

WARNING:

Several airbag system components get hot after

inflation. Do not touch them after inflation.

WARNING:

If the side

airbag has deployed,

the

airbag will not function again.
The side airbag system
(including the seat) must be
inspected and serviced by an
authorized dealer.

If the airbag

is not replaced, the unrepaired
area will increase the risk of injury
in a collision.

Determining if the system is operational

The SRS uses a readiness light in the instrument cluster or a tone to
indicate the condition of the system. Refer to

Warning lights and

chimes

in the

Instrument Cluster

chapter. Routine maintenance of the

side airbag is not required.

A difficulty with the system is indicated by one or more of the following:

•

The readiness light (same light as for front airbag system) will either
flash or stay lit.

•

The readiness light will not illuminate immediately after ignition is
turned on.

•

A series of five beeps will be heard. The tone pattern will repeat
periodically until the problem and/or light are repaired.

If any of these things happen, even intermittently, have the SRS serviced
at your authorized dealer immediately. Unless serviced, the system may
not function properly in the event of a collision.

Seating and Safety Restraints

209

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands