Ford 2012 F-150 Owner'S Manual Download Page 339

Page: 339 / 476

The fuses are coded as follows.

Fuse/Relay

Location

Fuse Amp

Rating

Protected Circuits

30A

Driver side front window

15A

SYNC

威

30A

Passenger side front window

10A

Interior lamps

20A

Memory module

Not used (spare)

7.5A

Power mirror switch, Memory seat
module

10A

Not used (spare)

10A

Radio display, GPS module,
Navigation display

10A

Run/accessory relay

10A

Instrument cluster

Roadside Emergencies

339

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands

Ford 2012 F-150, Owner'S Manual

Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands