manualshive.com logo in svg

Ford 2012 F-150, Owner'S Manual

Share
Download
Ford 2012 F-150 Owner'S Manual Download Page 359

Removing the jumper cables

Remove the jumper cables in the reverse order that they were
connected.

Note:

In the illustration, the vehicle on the bottom is used to designate

the assisting (boosting) battery.

1. Remove the jumper cable from
the ground metal surface.

2. Remove the jumper cable on the
negative (-) terminal of the booster
vehicle’s battery.

3. Remove the jumper cable from
the positive (+) terminal of the
booster vehicle’s battery.

4. Remove the jumper cable from
the positive (+) terminal of the
disabled vehicle’s battery.

After the disabled vehicle has been started and the jumper cables
removed, allow it to idle for several minutes so the engine computer can
relearn its idle conditions.

+

–

+

–

D

A

B

C

4

D

1

2

3

Roadside Emergencies

359

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands