Ford 2012 F-150 Owner'S Manual Download Page 46

Page: 46 / 476

FOR HILL DESCENT SELECT GEAR (if equipped)

— Displayed

when the driver is able to select a transmission gear for hill descent
mode.

HILL DESCENT - DRIVER RESUME CONTROL (if equipped)

—

Displayed when hill descent control mode is deactivated and the driver
must resume control.

HILL DESCENT CONTROL FAULT (if equipped)

— Displayed when

a hill descent system fault is present.

HILL DESCENT CONTROL OFF SYSTEM COOLING (if equipped)

— Displayed when the hill descent system is cooling due to overuse.

HILL DESCENT CONTROL READY (if equipped)

— Displayed

when the hill descent control switch is turned on.

REDUCE ACCELERATOR TO PREVENT WHEEL SLIP (if
equipped)

— Displayed when the vehicle senses that torque to the

drive wheels has overcome the available traction.

CAMERA MALFUNCTION (if equipped)

— Displayed when the front

camera is not operating properly.

Instrument Cluster

2012 F-150

(f12)

Owners Guide, 2nd Printing
USA

(fus)

Summary of Contents for 2012 F-150





























































































































































































































































































































































































































































































Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands

Ford 2012 F-150, Owner'S Manual

Search results

Summary of Contents for 2012 F-150

Reviews:

Brands by name

Popular brands