Fluke Biomedical medTester 5000C Operators Operator'S Manual Download Page 116

Page: 116 / 292

medTester 5000C

Operators Manual

8-2

Note

All medTester memory functions begin on

MENU2

as described

above.

Viewing A Single Record

You can view recorded tests from the medTester display.

Enter the menu command:

VIEW

The medTester prompts you:

RECORD # TO VIEW

. The total

number of records is displayed in parentheses. Enter the desired
record number.

View the record by scrolling through it with the up and down
arrow keys.

Printing Records

You can print records in a variety of ways with the printing option. To access
print options, enter the menu command:

PRINT

Print A Single Record

Enter the menu command:

SINGLE

Select the number of the record you want to print.

Summary of Contents for medTester 5000C Operators





































































































































































































































































































Search results

Summary of Contents for medTester 5000C Operators

Reviews:

Related manuals for medTester 5000C Operators

Brands by name

Popular brands

Fluke Biomedical medTester 5000C Operators, Operator'S Manual

Search results

Summary of Contents for medTester 5000C Operators

Reviews:

Related manuals for medTester 5000C Operators

Brands by name

Popular brands