manualshive.com logo in svg

Fluke Biomedical medTester 5000C Operators, Operator'S Manual

Share
Download
Fluke Biomedical medTester 5000C Operators Operator'S Manual Download Page 138

medTester 5000C

 

Operators Manual 

9-14 

Reinitialize Factory Default Settings 

Any customized autosequences can be returned to the factory default settings. 
To do this, enter these medTester commands: 

1.

 

From the medTester 5000C main menu, 

MENU

1, press the 

right arrow to access 

MENU2

. 

2.

 

Enter the command: 

CUSTOM

F3

 

3.

 

From the custom menu, press the right arrow and enter the 

command: 

INIT

F3

 

4.

 

Choose: 

DEFIB

F2

 

5.

 

To initialize defibrillator autosequences to defaults, press: 

YES

F5

 

Note 

Reinitializing will return all customized or created autosequences 
to factory default settings, including three blanks. 

 

Summary of Contents for medTester 5000C Operators





































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands