epiphan Pearl-2 Rackmount User Manual Download

Page: 465 / 497

Pearl-2 User Guide

Configuration keys for third party APIs

Table 84

Supported channel layout configuration keys

Key

Values

Description

active_layout

integer

Specifies which layout is currently active for the specified
channel.

Audio configuration keys

The following audio configuration keys are supported. For more information on individual items listed, see

Configure channel encoding

Table 85

Supported Audio configuration keys

Key

Values

Description

audio

on
empty string ("")

Enables or disables audio for the stream.
To enable audio, set to on.
To disable audio, set to an empty string ("").

audiobitrate

32
64
96
112
128
160
192

Specifies the audio bitrate for the stream.
Not applicable for PCM audio codecs.

audiochannels

1 (mono)
2 (stereo)

Specifies the number of audio channels.
For mono, set to 1.
For stereo, set to 2.

audiopreset

CODECS:
pcm_s161e  (PCM)
libmp3lame (MP3)
libfacc (AAC)

RATES:
16000 (AAC only)
22050
44100
48000

Specifies an audio code preset in the format CODEC;RATE.

i.e. libfaac;22050

452

Summary of Contents for Pearl-2 Rackmount


















































































































































































































































































































































































































































































































Search results

Summary of Contents for Pearl-2 Rackmount

Reviews:

Related manuals for Pearl-2 Rackmount

Brands by name

Popular brands

epiphan Pearl-2 Rackmount, User Manual

Search results

Summary of Contents for Pearl-2 Rackmount

Reviews:

Related manuals for Pearl-2 Rackmount

Brands by name

Popular brands