epiphan Pearl-2 Rackmount User Manual Download

Page: 297 / 497

Pearl-2 User Guide

Connect an RTSP source

The timestamps of an RTSP source and Pearl-2 tend to gradually go out of sync. If there's a

2500 –3000 ms

difference between the timestamp of your RTSP source and Pearl-2, a "no

signal" image displays and your RTSP source won't stream audio. Re-connect your RTSP
source to reset any time synchronization issues.

To connect an RTSP source to Pearl-2:

1. Login to the Admin panel as

admin

, see

Connect to the Admin panel

2. From the Inputs menu, click

Add input

, and then click

Add RTSP input

The RTSP input page opens.

284

Summary of Contents for Pearl-2 Rackmount


















































































































































































































































































































































































































































































































Search results

Summary of Contents for Pearl-2 Rackmount

Reviews:

Related manuals for Pearl-2 Rackmount

Brands by name

Popular brands

epiphan Pearl-2 Rackmount, User Manual

Search results

Summary of Contents for Pearl-2 Rackmount

Reviews:

Related manuals for Pearl-2 Rackmount

Brands by name

Popular brands