14
UltraProteus Operation Manual
0
BASIC OPERATION
IF ULTRAPROTEUS IS NOT
RESPONDING PROPERLY OR
PLAYS THE WRONG PRESET,
MAKE SURE THAT BOTH
ULTRAPROTEUS AND YOUR MIDI
CONTROLLER ARE SET TO THE
SAME MIDI CHANNEL AND THAT
THE MIDI VOLUME IS TURNED UP.
FOR MORE INFORMATION
ABOUT MIDI, SEE MIDI REALTIME
CONTROLS ON PAGE 97.
O
1
2
3
4
R A M P r e s e t s
R O M P r e s e t s
R A M H y p e r p r e s e t s
C a r d P r e s e t s
C a r d H y p e r p r e s e t s
Bank Contents
-
-
-
-
-
MIDI Channel
Program No.
Volume
Stereo Position
Program Name
Bank No.
CHANNEL PAN SHOULD
NORMALLY BE SET TO “P”
UNLESS REALTIME CONTROL OF
PANNING IS DESIRED. IF PAN IS
SET TO “0”, STEREO EFFECTS
CREATED IN THE PRESET WILL BE
LOST.
0
÷
MIDI Channel Parameters
÷
Preset/Hyperpreset Name
MIDI CHANNEL SELECTION
Press the cursor key repeatedly until the cursor is underneath the channel
number. (The cursor is the little flashing line underneath one of the parameters
in the display.) Rotate the data entry control to select MIDI channel 01-16. As
the channel is changed, the display will change to show the preset/hyperpreset,
volume and pan associated with the displayed channel.
C01 VOL127 PAN=P
000 Preset Name
PRESET/HYPERPRESET (PROGRAM) SELECTION
Press the cursor key repeatedly (or press Home/Enter) until the cursor is
underneath the program number. A Program is a Preset or a Hyperpreset. As
the data entry control is rotated, the program number and name will change.
The displayed program will be assigned to the displayed MIDI channel. Pro-
grams are arranged into banks of 128, as shown in the diagram at left. Banks
can be selected independently of the program number by pressing the Home/
Enter button while turning the data entry knob.
C01 VOL127 PAN=P
000 Program Name
CHANNEL VOLUME
Press the cursor key repeatedly until the cursor is underneath the volume value.
Rotate the data entry control to select volume 000-127. (This is the same
parameter as MIDI volume control #7, and changes made over MIDI will be
shown in the display.)
CHANNEL PAN
Press the cursor key repeatedly until the cursor is underneath the pan value.
Rotate the data entry control to select pan values -7 to +7 or “P”. When “P” is
selected, the pan value specified in the preset is selected. Any other value will
override the pan parameter in the preset. (This is the same parameter as MIDI
pan control #10, and changes made over MIDI will be shown in the display.)
Summary of Contents for Ultraproteus
