15 ENGLISH
1.
Loosen the tank cap a little to release the tank
pressure.
2.
Detach the tank cap, and refuel gently, while
discharging air by tilting the fuel tank so that the refuel
port is oriented upward. DO NOT fill up to the top.
3.
After refuelling, securely tighten the tank cap.
1
2
►
1.
Fuel tank
2.
Fuel tank cap
OPERATION
WARNING:
Be extremely careful to maintain
control of the machine at all times. Do not allow
the machine to be deflected toward you or anyone
in the work vicinity.
Failure to keep maintain of the
machine could result in serious injury to bystanders
and/or the operator.
Starting the engine
WARNING:
Never attempt to start the engine
where refueling is performed. Doing so may
cause ignition or a fire. When starting the engine,
maintain a distance of at least 3 meters from
refueling site.
WARNING:
Be sure that the cutting tool is
not in contact with the ground or any other object
before starting the engine.
WARNING:
Be sure that there are no fuel
leaks before starting the engine.
WARNING:
When pulling the starter handle,
kneel down and hold the tool with one hand to
keep a good balance.
When the engine is cold or after
refueling (cold start)
1.
Place the engine on a flat surface.
2.
Continue to push the primer pump until fuel enters
the primer pump.
1
►
1.
Primer pump
3.
Lift the choke lever to the closed position.
1
►
1.
Choke lever
4.
Pull the starter handle gently until it is hard to pull
(compression point). Then return the starter handle and
pull it strongly.
1
►
1.
Starter handle
NOTICE:
Never pull the rope to its full
extension.
NOTICE:
Return the starter handle to the hous
-
ing manually.
If you just release the starter handle, it
may hit your body or may not rewind appropriately.
Summary of Contents for MS290.4L
