22 ENGLISH
3.
Detach the plug cap and remove the spark plug
with the box wrench.
1
►
1.
Spark plug
4.
The appropriate clearance between the two
electrodes of the spark plug is 0.7 mm (0.028″) to 0.8
(0.031″) mm. Adjust the clearance if it is too wide or too
narrow.
Clean thoroughly or replace the spark plug if it has
accumulated carbon or is contaminated.
For replacement, use NGK CMR6H.
0.7 mm - 0.8mm
(0.028″ - 0.031″)
5.
Install the spark plug and attach the plug cap, and
then attach the plug cover.
Greasing the gear case
Interval for refilling:
Every 30 operating hours
Usable grease:
Shell Alvania 2 or equivalent
Remove the bolt on the gear case and refill with grease.
1
2
►
1.
Grease hole
2.
Bolt
NOTE:
You can purchase genuine Dolmar/Makita
grease from your Dolmar/Makita dealer.
Cleaning the fuel filter
CAUTION:
Be sure there is no damage to
the fuel tank.
If there is any damage to the fuel tank,
ask your authorized service center immediately for
repairs.
NOTICE:
Clean the fuel filter regularly.
A clogged
or damaged fuel filter can cause insufficient fuel sup
-
ply, which leads to difficulty starting up and reduced
engine power. Replace the fuel filter at least quarterly
to ensure satisfactory fuel supply to the carburetor.
Interval for cleaning and inspection:
Monthly (every
50 operating hours)
To clean the fuel filter, perform the following procedures.
1
2
3
►
1.
Fuel filter
2.
Hose clamp
3.
Fuel pipe
1.
Remove the fuel tank cap and empty the fuel tank.
2.
Check the tank inside for any foreign materials. If
there are any foreign materials, wipe them out.
3.
Pull out the fuel filter using a wire through the fuel
filling port.
4.
If the fuel filter surface is contaminated, clean it
with gasoline.
NOTICE:
Follow the method specified by each
local authority for disposing of the gasoline used
for cleaning the fuel filter.
NOTICE:
Replace the fuel filter if it is exces
-
sively contaminated.
5.
After checking, cleaning or replacing the fuel filter,
insert it into the fuel pipe and attach it with the hose
clamp. Reset the fuel filter in the fuel tank and tighten
the fuel tank cap firmly.
Summary of Contents for MS290.4L
