Danfoss FC 300, Programming Manual

Page: 132 / 205

[87] Alarm (trip lock)
Alarm (trip lock)
[87] A (Trip lock) alarm is active.
[90] Bus OK Bus OK [90] Active communication (no time-out) via the serial communication port.
[91] Torque limit & stop Torque limit & stop [91] If the frequency converter has received a stop signal and is at the torque limit, the
signal is logic “0”.
[92] Brake fault (IGBT)
Brake fault (IGBT)
[92] The brake IGBT is short circuited.
[93] Mech. brake control
Mech. brake control
[93] The mechanical brake is active.
[94] Safe stop active (FC
302 only) Safe stop active (FC 302 Only) [94] Safe stop is active DI 37.
[100] Comparator 0 Comparator 0 [100] The result of comparator 0.
[101] Comparator 1
Comparator 1
[101] The result of comparator 1.
[102] Comparator 2
Comparator 2
[102] The result of comparator 2.
[103] Comparator 3 Comparator 3 [103] The result of comparator 3.
[104] Comparator 4 Comparator 4 [104] The result of comparator 4.
[105] Comparator 5
Comparator 5
[105] The result of comparator 5.
[110] Logic rule 0
Logic rule 0
[110] The result of Logic rule 0.
[111] Logic rule 1 Logic rule 1 [111] The result of Logic rule 1.
[112] Logic rule 2 Logic rule 2 [112] The result of Logic rule 2.
[113] Logic rule 3
Logic rule 3
[113] The result of Logic rule 3.
[114] Logic rule 4
Logic rule 4
[114] The result of Logic rule 4.
[115] Logic rule 5 Logic rule 5 [115] The result of Logic rule 5.
[120] SL Time-out 0 SL Time-out 0 [120] The result of SLC timer 0.
[121] SL Time-out 1
SL Time-out 1
[121] The result of SLC timer 1.
[122] SL Time-out 2
SL Time-out 2
[122] The result of SLC timer 2.
[123] SL Time-out 3 SL Time-out 3 [123] The result of SLC timer 3.
[124] SL Time-out 4 SL Time-out 4 [124] The result of SLC timer 4.
[125] SL Time-out 5
SL Time-out 5
[125] The result of SLC timer 5.
[126] SL Time-out 6
SL Time-out 6
[126] The result of SLC timer 6.
[127] SL Time-out 7 SL Time-out 7 [127] The result of SLC timer 7.
[130] Digital input DI18 Digital input DI18 [130] Digital input 18. High = True.
[131] Digital input DI19
Digital input DI19
[131] Digital input 19. High = True.
[132] Digital input DI27
Digital input DI27
[132] Digital input 27. High = True.
[133] Digital input DI29 Digital input DI29 [133] Digital input 29. High = True.
[134] Digital input DI32 Digital input DI32 [134] Digital input 32. High = True.
[135] Digital input DI33
Digital input DI33
[135] Digital input 33. High = True.
[150] SL digital output A
SL digital output A
[150] Use the result of the SLC output A.
[151] SL digital output B SL digital output B [151] Use the result of the SLC output B.
[152] SL digital output C SL digital output C [152] Use the result of the SLC output C.
[153] SL digital output D
SL digital output D
[153] Use the result of the SLC output D.
[154] SL digital output E
SL digital output E
[154] Use the result of the SLC output E.
[155] SL digital output F SL digital output F [155] Use the result of the SLC output F.
[160] Relay 1 Relay 1 [160] Relay 1 is active
[161] Relay 2
Relay 2
[161] Relay 2 is active
[180] Local ref. active
Local ref. active
[180] High when par. 3-13 “Reference site” = [2] Local or when par 3-13 is [0] Linked to hand
Auto, at the same time as the LCP is in Hand on mode.
[181] Remote ref. active Remote ref. active [181] High when par. 3-13 “Reference site” = [1] Remote or [0] Linked to hand/auto, while
the LCP is in Auto on mode.
[182] Start command Start command [182] High when there is an active start command, and no stop command.
[183] Drive stopped
Drive stopped
[183] A stop command ( Jog, Stop, Qstop, Coast) is issued – and not from the SLC itself.
2. How to Programme FC 300 Programming Guide
132
MG.33.M3.02 - VLT ® is a registered Danfoss trademark
2