Danfoss FC 300, Programming Manual

Page: 131 / 205

[3] Motor speed
Motor speed
[3] [RPM] or [Hz]
[4] Motor current Motor current [4] [A]
[5] Motor torque Motor torque [5] [Nm]
[6] Motor power
Motor power
[6] [kW] or [hp]
[7] Motor voltage
Motor voltage
[7] [V]
[8] DC-link voltage DC-link voltage [8] [V]
[9] Motor thermal Motor thermal [9] Expressed as a percentage.
[10] VLT thermal
VLT thermal
[10] Expressed as a percentage.
[11] Heat sink temp.
Heat sink temp
[11] Expressed as a percentage.
[12] Analog input AI53 Analog input AI53 [12] Expressed as a percentage.
[13] Analog input AI54 Analog input AI54 [13] Expressed as a percentage.
[14] Analog input AIFB10
Analog input AIFB10
[14] [V]
[15] Analog input AIS24V
Analog input AIS24V
[15] [V] Analog input AICCT [17] [°].
[17] Analog input AICCT
[18] Pulse input FI29 (FC
302 only) Pulse input FI29 (FC 302 Only) [18] Expressed as a percentage.
[19] Pulse input FI33
Pulse input FI33
[19] Expressed as a percentage.
[20] Alarm number
Alarm number
[20] The error number.
[30] Counter A Counter A [30] Number of counts
[31] Counter B Counter B [31] Number of counts
[50] False
False
[50] Enters the fixed value of false in the comparator.
[51] True
True
[51] Enters the fixed value of true in the comparator.
[52] Control ready Control ready [52] The control board receives supply voltage
[53] Drive ready Drive ready [53] The frequency converter is ready for operation and applies a supply signal on the control board.
[54] Running
Running
[54] The motor is running.
[55] Reversing
Reversing
[55] The output is high when the frequency converter is running counter clockwise (the logical product
of the status bits “running” AND “reverse”)
[56] In range In range [56] The motor is running within the programmed current and speed ranges set in par. 4-50 to par.
4-53.
[60] On reference On reference [60] The motor is running on reference.
[61] Below reference, low
Below reference, low
[61] The motor is running below the value given in par. 4-54 “Warning Reference Low”
[62] Above reference, high
Above reference, high
[62] The motor is running above the value given in par. 4-55 “Warning Reference High”
[65] Torque limit Torque limit [65] The torque limit, set in par. 4-16 or 4-17, has been exceeded.
[66] Current limit Current limit [66] The motor current limit, set in par. 4-18, has been exceeded.
[67] Out of current range
Out of current range
[67] The motor current is outside the range set in par. 4-18.
[68] Below I low
Below I low
[68] The motor current is lower than set in par. 4-50.
[69] Above I high Above I high [69] The motor current is higher than set in par. 4-51.
[70] Out of speed range Out of speed range [70] The speed is outside the range set in par. 4-52 and 4-53.
[71] Below speed low
Below speed low
[71] The output speed is lower than the setting in par. 4-52.
[72] Above speed high
Above speed high
[72] The output speed is higher than the setting in par. 4-53.
[75] Out of feedb. range Out of feedb. Range [75] The feedback is outside the range set in par. 4-56 and 4-57.
[76] Below feedb. low Below feedb. Low [76] The feedback is below the limit set in par. 4-56.
[77] Above feedb. high
Above feedb. High
[77] The feedback is above the limit set in par. 4-57.
[80] Thermal warning
Thermal warning
[80] The thermal warning turns on when the temperature exceeds the limit in the motor, the
frequency converter, the brake resistor or thermistor.
[82] Mains out of range Mains out of range [82] The mains voltage is outside the specified voltage range.
[85] Warning Warning [85] A warning is active.
[86] Alarm (trip)
Alarm (trip)
[86] A (trip) alarm is active.
FC 300 Programming Guide 2. How to Programme
MG.33.M3.02 - VLT ® is a registered Danfoss trademark
131
2