manualshive.com logo in svg

Chevrolet 2002 Monte Carlo, Owner'S Manual, Page: 321 / 387

Share
Download
Chevrolet 2002 Monte Carlo Owner'S Manual Download Page 321

6-45

Any time you adjust a tire’s pressure, rotate your tires,
or have one or more tires repaired or replaced, you’ll
need to reset (calibrate) the tire inflation monitor
system. You’ll also need to reset the system whenever
you buy new tires and whenever the vehicle’s battery
has been disconnected.

To reset (calibrate) the system: The tire inflation
monitor system can be reset by turning the exterior lamp
control from OFF to parking lamps three times while the
ignition is in ON. It can also be reset through the radio
using the following steps:

1. Turn the ignition to ACC or ON and turn the 

radio off.

2. Press and hold the TUNE DISP button on the 

radio for at least five seconds until SETTINGS 
is displayed.

3. Press the SEEK PSCAN up or down arrow to scroll

through the main menu.

4. Scroll until TIRE MON appears on the display.

5. Press the 1 PREV or 2 NEXT button to enter the

submenu. RESET will be displayed.

6. Press the TUNE DISP button to reset. A chime will

be heard to verify the new setting and DONE will be
displayed for one second.

7. Once the monitor has been reset, scroll until EXIT

appears on the display.

8. Press the TUNE DISP button to exit programming.

A chime will be heard to verify exit.

The system completes the calibration process 
during driving.

The system normally takes 15 to 20 minutes of driving
in each of three speed ranges to “learn” tire pressures.
The speed ranges are 15 to 40 mph (25 to 65 km/h), 
40 to 65 mph (65 to 105 km/h) and above 65 mph 
(105 km/h). When learning is complete, the system 
will alert you after two to eight minutes if a tire is 12 psi
(83 kPa) different from the other three tires. Detection
thresholds may be higher and detection times may be
longer on rough roads, curves and at high speeds. 
The system is not capable of detection at speeds 
greater than 70 mph (110 km/h).

Summary of Contents for 2002 Monte Carlo




































































































































































































































































































































































































Reviews:

No comments