Chapter 17
17-50
SLP-SLCT
Use it enable/disable use of an existing network-based application.
setting
0: do not use (default)
1: use
When set to '1', no shift takes place to sleep mode 3.
2
PS-MODE
Use it to set PS compatibility mode.
setting
0: not compatible (default)
1: offer PS type 3 halftone command compatibility (dither reverse)
2: compatible with priority on resolution
3: reserved
4: compatible for EFI landscape/portrait mix
5 to 65535: reserved
2
CNCT-RLZ
Use it to enable/disable the use of the connection serialization function.
setting
0: off (disable connection serialization function; default)
1: on (enable connection serialization function)
2
INS-C/S
Expand the inserter function. (Only for a finisher inserter)
Setting value:
0: Front cover only (default)
1: Multiple inserters of "front cover + inserted cover"
MEMO:
- This mode is only available for a finisher inserter. (A perfect binder inserter always supports multiple inserters of "front cover +
inserted cover".)
- This setting is validated for both copying and printing operation.
2
PDL-NCSW
Set the card management mode for print jobs.
Control PDL print jobs using a New Card.
- Conventional operation
A PDL print job was received by the machine and printing was performed, regardless of whether or not a New Card was inserted.
(Job entry was controlled by the driver on the host side.)
- Operation after change
When this mode is set to "0", the machine operates in the same manner as the conventional operation.
When this mode is set to "1" and when a card is not inserted and the section ID does not match the card ID, printing is not performed.
When this mode is set to "1" and when the card ID does not match the section ID of the job after a card is inserted, printing is
performed.
Setting range:
0: A PDL print job is received by the machine and printing is performed regardless of whether or not a New Card is inserted.
[Factory setting value / Value after RAM clear]
1: When a card is not inserted and the section ID does not match the card ID, printing is not performed.
Factory setting value: 0
2
DOM-ADD
Set whether or not to supplement the destination domain for email transmission.
Perform transmission with an address in which the address entered for email transmission and the domain specified in the user mode
(ex. @xxxx.co.jp) are combined.
Setting value:
0: Do not supplement the domain. (default)
1: Supplement the domain.
<To send email to "[email protected]">
1) Specify "xxxx.co.jp" for the domain in the user mode, and specify "1" for this mode.
2) If "aaaa" is entered for email transmission, the address is supplemented as "[email protected]".
2
CLR-TIM
Set the timing of complete deletion of processing data.
Select the timing to execute complete deletion using the security kit.
When complete deletion is executed, performance of job processing may decrease depending on the data. This occurs because
processed page data is deleted during job processing and much load is applied to the processing to access the CPU or HDD. When
this processing is performed after job processing is completed, job processing capability can be improved.
Setting range: 0, 1 (0: Delete data during job processing. 1: Delete data after job processing is completed.)
Factory setting value: 0
2
FREE-DSP
Charging/non-charging indication switch
When a vendor does not have a hardware switch that changes charging/non-charging indication, a software switch is needed. If
such is a case, this mode can be used whether to display the software switch.
0: not display (default)
1: display
Only supports iR5075/5065/5055 Series V2. (BODY No. CHL XXXX, CHM XXXX, CHN XXXX, CHP XXXX, CHQ XXXX,
CHU XXXX, CHV XXXX, CHW XXXX, CHZ XXXX, CJA XXXX, CJD XXXX, CJJ XXXX, CJK XXXX, CJP XXXX, CJQ
XXXX, CJR XXXX, CJU XXXX, CJZ XXXX, CKA XXXX, CKC XXXX, CKD XXXX, CKE XXXX)
2
COPIER > OPTION >USER
Sub-item
Description
Level
Summary of Contents for iR5055
