Chapter 10
10-19
F-10-46
10.5.2 Left Deck Drive Assembly
10.5.2.1 Before Removing the Left Deck Drive Assembly
0015-5083
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).
(page 10-22)
Reference[Removing the Charger unit]
2) Remove the rear cover (upper).
(page 10-13)
Reference[Removing the
Rear Cover (Upper)]
3) Detach the rear cover (lower).
(page 10-13)
Reference[Removing the
Rear Cover (Lower)]
4) Remove the HVT PCB.
(page 10-28)
Reference[Removing HVT PCB]
10.5.2.2 Removing the Left Deck Drive Assembly
0015-5085
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the left deck drive assembly [4].
- 4 screws [1]
- 1 connector [2]
- 2 wire saddles [3] (Free the harness)
F-10-47
10.5.3 Manual Feed Pickup Drive Assembly
10.5.3.1 Before Removing the Manual Pickup Drive
Assembly
0015-5086
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).
(page 10-22)
Reference[Removing the Charger unit]
2) Remove the rear cover (upper).
(page 10-13)
Reference[Removing the
Rear Cover (Upper)]
3) Remove the rear cover (lower).
(page 10-13)
Reference[Removing the
Rear Cover (Lower)]
4) Remove the main controller box cover.
(page 10-17)
Reference[Remov-
ing the Main Controller Box Cover]
5) Remove the right cover (upper rear).
(page 10-12)
Reference[Removing
the Right Cover (Upper Rear)]
6) Remove the main controller box.
(page 4-13)
Reference[Removing the
Main Controller Box]
7) Remove the separation claw AC PCB unit.
(page 10-28)
Reference[Re-
moving Separation Claw AC PCB]
10.5.3.2 Removing the Manual Pickup Drive Assembly
0015-5089
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the scanner fan duct [2].
- 2 screws [1]
Before removing the screw, make sure to mark the line in the following step.
2) Loosen the screw [3] to release the belt tensioner [4], and detach the belt
[5].
F-10-48
3) Remove the pickup drive assembly [3].
- 4 screws [1]
- 3 connectors [2]
F-10-49
10.5.4 Vertical Path Drive Assembly
10.5.4.1 Before Removing the Vertical Path Drive
Assembly
0015-5090
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the charger unit (this step is necessary only for iR5075 for Japan).
(page 10-22)
Reference[Removing the Charger unit]
2) Remove the rear cover (upper).
(page 10-13)
Reference[Removing the
Rear Cover (Upper)]
3) Detach the rear cover (lower).
(page 10-13)
Reference[Removing the
Rear Cover (Lower)]
4) Detach the main controller box cover.
(page 10-17)
Reference[Remov-
ing the Main Controller Box Cover]
5) Removing the Right Cover (Upper Rear).
(page 10-12)
Reference[Re-
moving the Right Cover (Upper Rear)]
6) Remove the main controller box.
(page 4-13)
Reference[Removing the
Main Controller Box]
7) Detach the right cover (lower rear).
(page 10-12)
Reference[Removing
the Right Cover (Lower Rear)]
8) Remove the collecting toner bottle holder.
(page 5-29)
Reference[Re-
moving the Collecting Toner Bottle Holder]
10.5.4.2 Removing the Vertical Path Drive Assembly
0015-5096
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Disconnect the 10 connectors on the motor driver PCB .
2) Detach the motor driver PCB mounting base [3].
- 9 wire saddles (Free the harness [1])
- 4 screws [2]
[1]
[1]
[2]
[3]
[1]
[1]
[1]
[2]
[3]
[3]
[4]
[1]
[1]
[4]
[3]
[2]
[5]
[1]
[2]
[2]
[1]
[3]
Summary of Contents for iR5055
