Chapter 5
5-6
F-5-9
[1] Scanner Motor M501 Drive Signal
starts/stops the motor; controls the direction and speed of its rotation
[2] Scanner HP Detection Signal
detects the presence of the No. 1 mirror base at home position
5.3.1.2 Controlling the Scanner Motor
0015-4389
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
The configuration of the system used to control the scanner motor is as follows; the motor driver on the interface PCB operates according to the signals from the
CPU to start/stop the scanner motor and to control the direction and speed of its rotation
F-5-10
1. Reverse Movement After a Scan
After an image scan, the No. 1 mirror base is moved in reverse as far as the shading position at 234 mm/sec regardless of the selected magnification.
2. Forward Movement During a Scan
During an image scan, the No. 1 mirror base is controlled at the speed indicated in the following figure; the No. 1 mirror base is moved forward at 325 mm/sec for
100% magnification.
F-5-11
[1]
[2]
Reader
controller
PCB
Interface
PCB
(forward)
(reverse)
Scanner motor
Light-blocking plate
No.2 mirror
base
Scanning
lamp
No.1 mirror base
Scanner
HP sensor
Reader controller PCB
Motor
driver
Interface PCB
+24V/15V
J306
A
A*
B
B*
CPU
1
2
3
4
6
5
J308
J307
J202
J203
Scanner
motor
M501
[1]
[1] Scanner motor control signal
Start
position
Acceleration
Image leading edge
Constant speed
Image trailing edge
Deceleration
Stop
Shift
speed
Shift distance
[1]
[2]
[3]
[4]
[1] Acceleration interval: accelerates up to scan speed
[2] Run-up interval: run-up margin used to ensure stable speed
[3] Image read interval: segment over which images are read
[4] Deceleration interval: at the image trailing edge, decelerates and stops as soon as possible
HP
Summary of Contents for iR5055
