Chapter 17
17-24
T-17-16
<ADJ-XY>
T-17-17
<CCD>
T-17-18
<LASER>
T-17-19
<DEVELOP>
COPIER > ADJUST > AE
Sub-item
Description
Level
AE-TBL
adjustment range: 1 to 9 (default: 5)
- to obtain darker characters, increase the setting.
- to obtain lighter characters, decrease the setting.
If you have initialized the RAM on the reader controller PCB, enter the value indicated on the service label.
1
COPIER > ADJUST > ADJ-XY
Sub-item
Description
Level
Use it to adjust the image read start position.
- If you have initialized the RAM on the reader controller PCB or replaced the PCB, enter the value indicated on the service label.
- If you have changed the setting of this item, record the new setting on the service label.
ADJ-X
Use it to adjust the image read start position (X direction).
adjustment range: 1 to 100 (default: 26)
1
ADJ-Y
Use it to adjust the image read start position (Y direction).
adjustment range: 200 to 500 (default: 352)
1
ADJ-Y-DF
Use it to adjust the main scanning position for feeder mode.
adjustment range: 100 to 400 (default: 248)
1
STRD_POS
Use it to adjust the CCD read position for DF stream reading mode.
adjustment range: 1 to 200 (default: 100)
1
ADJ-X-MG
Fine adjustment of magnification in sub scanning direction at copyboard reading
adjustment range: -50 to 50 (default: 0)(unit: 0.01%)
1
ADJ-Y-DF2
Adjustment of the position on the backside in main scanning direction at simultaneous double-sided reading
adjustment range: 21 to 106 (default: 76)
1
COPIER > ADJUST > CCD
Sub-item
Description
Level
SH-TRGT
Use it to enter the white level target value for shading correction.
adjustment range: 1 to 2047 (default: 1136)
1
DFTAR-G
Use it to adjust the shading target value for green for DF mode.
adjustment range: 1 to 2047 (default: 1189)
1
MTF-M1
Setting value of front/back matching MTF in main scanning direction (front).
adjustment range: 20 to 80 (default: 50)
1
MTF-M2
Setting value of front/back matching MTF in main scanning direction (center).
adjustment range: 20 to 80 (default: 50)
1
MTF-M3
Setting value of front/back matching MTF in main scanning direction (back).
adjustment range: 20 to 80 (default: 50)
1
MTF-S1
Setting value of front/back matching MTF in sub scanning direction.
adjustment range: 20 to 80 (default: 50)
1
DFCH2G2
Setting of linearity characteristic data value of No. 2 data (Green) of DF composite chart for CCD.
adjustment range: 1 to 2550 (default: 2000)
1
DFCH2G10
Setting of linearity characteristic data value of No. 10 data (Green) of DF composite chart for CCD.
adjustment range: 0 to 2550 (default: 0)
1
DFCH-G10
Setting of linearity characteristic data value of No. 10 data (Green) of DF composite chart for CIS.
adjustment range: 0 to 2550 (default: 0)
1
DFCH-G2
Setting of linearity characteristic data value of No. 2 data (Green) of DF composite chart for CIS.
adjustment range: 1 to 2550 (default: 2000)
1
COPIER > ADJUST > LASER
Sub-item
Description
Level
PVE-OFST
Use it to adjust the laser write start position.
adjustment range: -300 to 300
1
POWER
Use it to adjust the laser power (for non-potential control).
adjustment range: 0 to 255
1
Summary of Contents for iR5055
