Chapter 7
7-4
A. Timing and particulars of potential control
1. At the time of warm-up
The machine's potential control consists of copier potential control mechanisms and printer potential control mechanisms.
The machine uses VD=390V for both copier and printer control mechanisms.
The timing of potential control is as follows:
T-7-3
2. In the service mode
If enabled in service mode, potential control starts 10 min and 60 min after the main power switch is turned on or when the door is opened and closed. The timing
and particulars of potential control are as follows:
T-7-4
B. Sequence of potential control
1. At the time of warm-up
F-7-6
The sequence and particulars of potential control are as follows:
[1] copier potential control: VD = 8 times max.; VL1 = 8 times max.; VL2 = once
[2] printer potential control: VD = 8 times max.; VL1 = 8 times max.; VL2 = once
SERVICE MODE:
At time of warm-up
Purpose
to execute potential control for copier/printer mode
to determine a constant value for copier/printer mode
Operating condition
- the temperature of the fixing assembly is 50 deg C or lower when the main power
switch is on
- when the first image is being formed 60 min after warm-up
Operation length
10 sec (approx.)
Service mode
may be enabled or disabled using the following: COPIER>OPTION>BODY>PO-
CNT
Default
ON (potential control for both copier and printer modes)
10 min and 60 min after the main power switch is turned on
Purpose
to control sensitivity, thus making up for changes in drum temperature
to accommodate changes in charging efficiency
Operating conditions
- start of the 1st job 10 min and 60 min after the main power switch has been turned
on
- the door is opened and closed
Operation length
off: is not executed (default)
short mode: about 5 sec
standard mode: about 10 sec
service mode
settings may be OFF, short, or standard as determined by the following:
COPIER>OPTION>BODY>PO-CNTMD
Default
OFF
WMUPR
WMUP
STBY
Fixing assembly temperature 195 C
200 C
Drum motor (M1)
Primary charging
Laser
Potential sensor
Printer potential control [2]
Copier potential control [1]
VD VD VD VL1
VL2
VL1
VD VD VD VL1
VL2
VL1
Summary of Contents for iR5055
