Canon iR5055, Service Manual

Page: 517 / 646

Chapter 16
16-17
T-16-4
T-16-5
XX YY
XX
CHK-
TYPE
Partition Description
At start-up During operation
03 05 00,01,02,04
11,2
1
13,2
5
10,12,14,22,23,24
Remedy Remedy
01
1
FSTDEV compressed image data (e.g., Box)
*1 *5
*9 *10 *11 *12
02 IMG_MNG
file management table, profile
03 FSTCDEV job archiving (chasing)
04
2
APL_GEN general data
05 TMP_GEN
general data (temporary file)
06 TMP_FAX
for fax (temporary file)
07 TMP_PSS
for PDL spool (temporary file)
08 3 PDLDEV
for PDL spool (e.g., font)
09 4 BOOTDEV
firmware (system, MEAP, key, certificate,
PDF dictionary, RUI content, audio
dictionary)
*3 *8
10 5 APL_MEAP MEAP application *1 *5
11 6 APL_SEND address book, filter *2 *5
12 7 APL_KEEP
MEAP save data
*3 *8
13 8 APL_LOG
System log saving capacity
*1 *5
FF 0
Not
identified
full check on HDD for faulty sector and
recovery
*4 *7
YY Description Remedy
*1
03
An ongoing write operation
is interrupted (at start-up).
1. Set '0' to CHK-TYPE, and execute HD-CHECK; then, turn off and then back on the power.
2. Type in CHK-TYPE that corresponds to the partition in question, and execute HD-CLEAR; then, turn off and
then back on the power.
*2
1. Ask the user to download the address book data using a remote UI.
2. Set '0' to CHK-TYPE, and execute HD-CHECK; thereafter, turn off and then on the power.
3. Start download mode, and execute full formatting using the SST; thereafter, turn off and then back on the power.
*3
The recovery operation for the boot partition necessarily requires the use of the SST in safe mode.
1. Set '0' for CHK-TYPE, and execute HD-CHECK; thereafter, turn off and then back on the power.
2. Start download mode, and execute full formatting and re-install the system software; thereafter, turn off and
then back on the power.
*4
1. Set '0' to CHK-TYPE, and execute HD-CHECK; then, turn off and then back on the power.
2. Execute HD-CLEAR by setting '1', '2', '3', and '5' to CHK-type; then, turn off and then back on the power.
*5
05
A file system error has
occurred.
1. Type in CHK-TYPE corresponding to the partition in question, and execute HD-CLEAR; then, turn off and then
back on the power.
2. Replace the HDD, and re-install the system software.
*6
The machine does not permit execution of HD-CLEAR in service mode (to prevent loss of partition information
such as address book and filter data).
1. Ask the user to download the address book data using a remote UI.
2. Start download mode from service mode; then, execute full formatting using
the SST, and re-install the system software. Thereafter, turn off and then back on the power.
*7
1. Execute HD-CLEAR by setting "1', '2', '3', and '5' to CHK-TYPE; then, turn off and then back on the power.
2. Replace the HDD, and re-install the system software.
*8
Recovery operation for the Boot partition necessarily requires the use of the SST in safe mode.
1. Start in safe mode, and execute full formatting in the SST, and re-install the system software. Thereafter, turn
off and then on the power.
2. Replace the HDD, and re-install the system software.
*9
00
01
02
04
There is poor contact for the
HDD, or there is a system
error.
1. Check the cables and power cord for disconnection.
2. Start up in safe mode; then, execute full formatting using the SST, and re-install the system software. Thereafter,
turn off and then back on the power.
3. Replace the HDD, and re-install the system software.
*10
11
21 There is poor connection of
the HDD.
1. Check the cable and the power connectors for disconnection.
2. Replace the HDD, and re-install the system software.
*11
13
25 A write operation has been
suspended.
File data as of Box on the HDD may be damaged.
1. Set '0' for CHK-TYPE, and execute HD-CHECK; then, turn off and then back on the power.
2. Set '1' for CHK-TYPE, and execute HD-CLEAR.
(In the case of APL_SEND or BOOTDEV, reformat using the SST and re-install the system software.)
3. Replace the HDD, and re-install the system software.