manualshive.com logo in svg

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 98 / 136

Share
Download
Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 98

If the LED is not steady green, ensure that the power supply is securely installed and seated
properly.

You can enter one of the following commands at the command line prompt to display the power
supply status:

•

show chassis

•

show environment power

The power supply status can also be viewed using the Web Tools application.

Replacing an 1100W DC power supply

Use the following procedure to remove an 1100W AC power supply.

NOTE

Before beginning the replacement, refer to the precautions in the "Power precautions" section of this
guide.

1. If leaving the device in service while replacing a power supply, verify that the other power supply

(the one not being replaced) has been powered on for at least four seconds and has a steady green
status LED.

2. Unplug the DC wiring harness from the power supply that is being replaced.
3. Push the locking tab on the right lower corner of the power supply to the left and hold it there while

using the handle on the power supply to pull it straight out and away from the chassis. Pull the
power supply out slowly to avoid catching a finger on the locking tab.

Replacing an 1100W DC power supply

98

Brocade VDX 6940 Hardware Installation Guide

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments