manualshive.com logo in svg

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 100 / 136

Share
Download
Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 100

1

DC wiring harness from power source

2

Wiring harness connector on power
supply

3

DC power supply

4

Locking tab

FIGURE 52

 1100W DC power supply and DC harness

4. Place the power supply in an anti-static bag for storage.
5. If the empty power supply bay where you are installing the power supply has a cover plate, remove

the two screws near the edges of the cover plate to unlock the plate, and then remove the plate.

6. Remove the replacement power supply from its packaging.
7. To install the power supply into the chassis, orient the power supply with the locking tab on the

lower right, as shown in the previous illustration.

8. With one hand, hold the bar on the front panel of the power supply. With the other hand, support the

underside of the power supply, and insert the power supply into the empty power supply slot. Slide
the new power supply into the chassis until the locking tab engages.

NOTE

Do not force the installation. If the power supply does not slide in easily, ensure that the power
supply is correctly oriented before continuing.

9. Plug the DC cable harness into power supply connector.

The harness connector is keyed so that it fits only one way into the power supply.

10.Refer to 

Connecting a power cord to a 1100W DC power supply

 on page 34 for more information

and precautions on connecting DC power.

The equipment installation must meet NEC/CEC code requirements. Consult local authorities for
regulations.

Removal and Replacement Procedures

100

Brocade VDX 6940 Hardware Installation Guide

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments