manualshive.com logo in svg

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 38 / 136

Share
Download
Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 38

FIGURE 17

 Installing ground lug on Brocade VDX 6940-144S

4. Observe the following requirements and precautions when grounding this device:

•

NOTE

To ensure adequate bonding when attaching the ground lug, a minimum of 20 in-lb (2.76 Nm) of
torque is required to be applied to the mounting hardware used to attach the ground lug.

•

CAUTION
For the NEBS-compliant installation of a Brocade device with AC or DC systems, use a
ground wire of at least 6 AWG. The ground wire should have an agency-approved crimped
connector (provided with the device) attached to one end, with the other end attached to
building ground. The connector must be crimped with the proper tool, allowing it to be
connected to both ground screws on the enclosure. Before crimping the ground wire into
the provided ground lug, ensure that the bare copper wire has been cleaned and
antioxidant is applied to the bare wire. In addition, anti-rotation devices or lock washers
must be used with all screw connections for the grounding wire.

Observing power supply function

The following should occur after you apply power to the power supplies:

NOTE

Power is supplied to the device as soon as the first power supply is connected and powered on.

• The power supplies power up as soon as they are plugged in.
• The power supply LEDs display green.
• The power LED on the port-side of the device displays green.
• The system status LED on the port-side of the device displays amber until POST completes, and

then displays green.

After POST is complete, verify that the device power and status LEDs on the port side of the device
remain green.

Rack installation

You can install this device in the following racks:

• Four-post EIA rack
• Two-post Telco rack

Follow installation instructions shipped with the following rack-mount kits:

• Universal Four-Post Rack Kit (XBR-R000296) - Use this kit to install devices in EIA racks that are

between L-13.7 to 81.28 cm deep (L-5.0 to 32.0 in.), where L is the chassis depth. For installation
procedures, refer to the 

Universal Four-Post Rack Kit Installation Procedures

.

• Universal Two-Post Rack Kit (XBR-R000294) - Use this kit to install 1U and 2U devices in a two-

post telecommunications (Telco) rack. For installation procedures, refer to the 

Universal Two-Post

Rack Kit Installation Procedures

.

Observing power supply function

38

Brocade VDX 6940 Hardware Installation Guide

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments