manualshive.com logo in svg

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 105 / 136

Share
Download
Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 105

1

SFP or SFP+ bail

FIGURE 56

 Optical transceiver with bail open

Replacing a transceiver

Complete the following steps to replace an SFP or SFP+ transceiver. Refer to the illustration in 

Removing a transceiver

 on page 104.

1. Making sure that the bail (wire handle) is in the unlocked or open position, position the optical

transceiver so that the key is oriented correctly to the port. Insert the transceiver into the port until it is
firmly seated and the latching mechanism clicks.

Transceivers are keyed so that they can only be inserted with the correct orientation. If a transceiver
does not slide in easily, ensure that it is correctly oriented.

2. Position a cable so that the key (the ridge on one side of the cable connector) is aligned with the slot

in the transceiver. Insert the cable into the transceiver until the latching mechanism clicks.

Cables are keyed so that they can be inserted in only one way. If a cable does not slide in easily,
ensure that it is correctly oriented.

Replacing a transceiver

Brocade VDX 6940 Hardware Installation Guide

105

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments