manualshive.com logo in svg

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 131 / 136

Share
Download
Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 131

DANGER

Rayonnement de laser. Ne regardez pas directement avec les instruments optiques. Produits
de laser de la classe 1M.

PELIGRO

Radiacion de Laser. No vea directamente con Instrumentos Opticos. Clase 1M de Productos
de Laser.

Electrical dangers

DANGER
Connect the power cord only to a grounded outlet.

GEFAHR

Schließen Sie das Netzkabel nur an eine geerdete Steckdose an.

DANGER

Le cordon d’alimentation ne doit être raccordé qu’à une prise de courant mise à la terre.

PELIGRO

Conecte el cable de alimentación únicamente a una toma de corriente con conexión a tierra.

DANGER
Disconnect the power cord from all power sources to completely remove power from the device.

GEFAHR

Ziehen Sie das Stromkabel aus allen Stromquellen, um sicherzustellen, dass dem Gerät kein
Strom zugeführt wird.

DANGER

Débranchez le cordon d'alimentation de toutes les sources d'alimentation pour couper
complètement l'alimentation du dispositif.

PELIGRO

Para desconectar completamente la corriente del instrumento, desconecte el cordón de
corriente de todas las fuentes de corriente.

DANGER
This product is designed for an IT power system with phase-to-phase voltage of 230V. After
operation of the protective device, the equipment is still under voltage if it is connected to an IT
power system.

GEFAHR

Dieses Produkt ist für die Stromversorgung über ein IT-Stromversorgungssystem mit einer
Netzspannung von 230 V Phase zu Phase konzipiert. Bei einem Anschluss an ein IT-
Stromversorgungssystem steht das Gerät selbst dann unter Spannung, wenn die
Schutzvorrichtung ausgelöst wurde.

DANGER

Ce produit est conçu pour un système d’alimentation électrique avec une tension de 230 Ven
mono-phase. Après fonctionnement du dispositif de protection, l’équipement esttoujours sous
tension s’il est connecté à un système d’alimentation électrique

PELIGRO

Este es un producto diseñado para sistemas de alimentación informático con un voltaje de de
haber utilizado el dispositivo de protección, el equipo sigue teniendo voltaje si está conectado a
un sistema de alimentación informático.

Cautions and Danger Notices

Brocade VDX 6940 Hardware Installation Guide

131

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments