Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 91 | Manualshive

Page: 91 / 136

Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 91

FIGURE 46

Removing wiring harness from DC power supply

5. Loosen the wire tightening screws to remove the two wires from the DC power source, as shown in

following illustration, from the DC wiring assembly.

1

Wire tightening screws

2

Assembly screws

FIGURE 47

The DC wiring assembly

6. Reinstall the DC wiring assembly on the power supply so that you can return it with the power supply.
7. Place the power supply in an anti-static bag for storage.
8. If the empty power supply bay where you are installing the power supply has a cover plate, remove

the two screws near the edges of the cover plate to unlock the plate, and then remove the plate.

9. Remove the replacement power supply from its packaging.
10.Unscrew the two DC wiring harness assembly screws to unlock the wiring harness assembly from

the power supply, and then remove the assembly from the power supply.

11.Loosen the wire tightening screws and insert the wires from the DC power source into the wiring

assembly (as shown in the illustration below).

Removal and Replacement Procedures

Brocade VDX 6940 Hardware Installation Guide

91

53-1003495-02

«
...
89
90
91
92
93
...
»

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments