manualshive.com logo in svg

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 47 / 136

Share
Download
Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 47

1

Screws, 10-32 x 5/8-in., panhead
Phillips

2

Retainer nuts, 10-32

FIGURE 23

 Attaching the rear brackets to the rack posts

Installation procedure for flush-rear (recessed) mounting

The flush-rear (recessed) mounting is similar to the flush-front mounting except that the brackets are
reversed on the switch.

NOTE

The switch must be turned off and disconnected from the fabric during this procedure.

Complete these tasks to install the switch in a four-post rack:

•

Attaching the front brackets to the rear of the switch

 on page 47

•

Attaching the extensions to the front of the switch

 on page 48

•

Installing the switch in the rack

 on page 49

•

Attaching the rear brackets to the extensions at the front of the switch

 on page 50

•

Attaching the rear brackets to the front rack posts

 on page 52

Attaching the front brackets to the rear of the switch

NOTE

In this installation, the brackets are named as called out in the parts list even though the installation of
the brackets is reversed from the flush-front installation.

Installation procedure for flush-rear (recessed) mounting

Brocade VDX 6940 Hardware Installation Guide

47

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments