manualshive.com logo in svg

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 96 / 136

Share
Download
Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 96

NOTE

Power supplies are hot swappable. You can replace a one power supply at a time while the Brocade
device is powered on and running.

Installation precautions and warnings

Follow these precautions when installing a power supply in the Brocade device.

DANGER
Before beginning the installation, see the precautions in “Power precautions.”

CAUTION
Do not install the device in an environment where the operating ambient temperature might
exceed 40°C (104°F).

CAUTION
Never leave tools inside the chassis.

Replacing an 1100W AC power supply

Use the following procedure to remove an 1100W AC power supply.

NOTE

Before beginning the replacement, refer to the precautions in "Power precautions."

1. If leaving the device in service while replacing a power supply, verify that the other power supply

(the one not being replaced) has been powered on for at least four seconds and has a steady green
status LED.

2. Ensure that the replacement power supply has the same part number and airflow label as the power

supply being replaced.

3. Unplug the power cord from the power supply that is being replaced.
4. Push the locking tab on the right lower corner of the power supply to the left and hold it there while

using the handle on the power supply to pull it straight out and away from the chassis. Pull the
power supply out slowly to avoid catching a finger on the locking tab.

Installation precautions and warnings

96

Brocade VDX 6940 Hardware Installation Guide

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments