Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 94

Page: 94 / 136

FIGURE 49

Inserting or removing the fan assembly

5. Verify that the fan status LED is steady green to indicate normal operation.

If the LED is not steady green, ensure that the fan is securely installed and seated properly. You
can refer to the "Interpreting LED activity" section of this guide for details on LED operation.

You can enter one of the following commands at the command line prompt to display fan status:

•

show chassis

•

show environment fan

The fan status can also be viewed using the Web Tools application.

VDX 6940-144S FRU replacement

Field-replaceable units (FRUs) include separate power supplies and fan assemblies identified through
Network OS as follows:

• Power supplies - identified from top to bottom as power supply #1 and power supply #2 when

viewed from the non-port-side of the device.

• Fan assemblies - identified from left to right as fan #1, fan #2, fan #3, and fan #4 when viewed from

the non-port side of the device.

For locations of these assemblies, captive screws, LEDs, labels, and other components, refer to

Non-

port-side views

on page 24.

NOTE

Maintain all power supply and fan assemblies in operational condition to provide redundancy.

VDX 6940-144S FRU replacement

Brocade VDX 6940 Hardware Installation Guide

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Search results

Summary of Contents for VDX 6940 Series

Reviews:

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 94 / 136

Search results

Summary of Contents for VDX 6940 Series

Reviews: