manualshive.com logo in svg

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 132 / 136

Share
Download
Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 132

Dangers related to equipment weight

DANGER
Before beginning the installation, see the precautions in “Power precautions.”

GEFAHR

Vor der Installation siehe Vorsichtsmaßnahmen unter “Power Precautions”
(Vorsichtsmaßnahmen in Bezug auf elektrische Ablagen).

DANGER

Avant de commencer l'installation, consultez les précautions décrites dans “Power
Precautions” (Précautions quant à l'alimentation).

PELIGRO

Antes de comenzar la instalación, consulte las precauciones en la sección “Power
Precautions” (Precauciones sobre corriente).

DANGER
Make sure the rack housing the device is adequately secured to prevent it from becoming
unstable or falling over.

GEFAHR

Stellen Sie sicher, dass das Gestell für die Unterbringung des Geräts auf angemessene Weise
gesichert ist, so dass das Gestell oder der Schrank nicht wackeln oder umfallen kann.

DANGER

Vérifiez que le bâti abritant le dispositif est bien fixé afin qu'il ne devienne pas instable ou qu'il
ne risque pas de tomber.

PELIGRO

Verifique que el bastidor que alberga el instrumento está asegurado correctamente para evitar
que pueda hacerse inestable o que caiga.

Cautions and Danger Notices

132

Brocade VDX 6940 Hardware Installation Guide

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments