Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 71 | Manualshive

Page: 71 / 136

Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 71

optional. By default, this value is LOCL, which uses the local clock of the principal switch as the clock
server.

device(config)# ntp server "132.163.135.131"

To display the NTP server IP address, use the

show ntp status

rbridge-id

rbridge-id

|

all

command.

If you are in global configuration mode, you must enter

do

before the

show

command.

device(config)# show ntp status rbridge-id 1

The request is for the local RBridge unless an RBridge ID is specified.

If you need to remove an NTP server, use the

no

form of the

ntp server

command.

device(config)# no ntp server "132.163.135.131"

Setting the clock (date and time) manually

You should set the clock only if there are no NTP servers configured. Time synchronization from NTP
servers overrides the local clock. Date values are limited to between January 1, 1970 and January 19,
2038.

1. Log in to the device using the admin account.
2. Enter the

clock set CCYY-MM-DDTHH:MM:SS

command while in privileged EXEC mode.

The following example sets the clock to March 17, 2010, 15 minutes past noon:

device# clock set 2010-03-17T12:15:00

3. To show the clock and time zone settings, use the

show clock

rbridge-id

rbridge-id

|

all

command.

device# show clock

rbridge-id 1: 2012-03-17 12:15:00 America/Los_Angeles

Setting the time zone

You must perform this procedure on

all

devices for which the time zone must be set. However, you only

need to set the time zone once on each device, because the value is written to nonvolatile memory.
While not necessary for device operation, setting a time zone is part of ensuring accurate logging and
audit tracking. Time zone changes take effect after a reboot.

Use the

clock timezone

command to set the time zone.

1. Log into the device using an account that has the admin role.
2. Enter the

clock timezone

region/city

command.

The following example changes the time zone to US/Pacific Standard Time:

device# clock timezone America/Los_Angeles

3. Reboot the device.

Network device connections

Refer to the product Technical Specifications for a listing of supported cables.

Setting the clock (date and time) manually

Brocade VDX 6940 Hardware Installation Guide

71

53-1003495-02

«
...
69
70
71
72
73
...
»

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments