Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 89 | Manualshive

Page: 89 / 136

Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 89

FIGURE 44

Inserting the power supply

6. Place the power supply in an anti-static bag for storage.
7. If the empty power supply bay where you are installing the replacement power supply has a cover

plate, remove the two screws near the edges of the cover plate to unlock the plate, and then remove
the plate.

8. Remove the replacement power supply from its packaging.
9. To install the power supply into the chassis, orient the power supply with the power plug receptacle

on the right, as shown in the previous illustration.

10.With one hand, hold the bar on the front panel of the power supply. With the other hand, support the

underside of the power supply, and insert the power supply into the empty power supply slot. Gently
push the power supply into the chassis until it is firmly seated.

CAUTION
Carefully follow the mechanical guides on each side of the power supply slot and make sure
the power supply is properly inserted in the guides. Never insert the power supply upside
down.

NOTE

Do not force the installation. If the power supply does not slide in easily, ensure that the power
supply is correctly oriented before continuing.

11.Secure the power supply to the chassis by tightening the two captive screws using the Phillips

screwdriver.

12.Plug the power cord from the AC power source into the power supply to power on the unit.

The power supply will immediately attempt to power up.

CAUTION
If you observe that the switch has powered down approximately two minutes after a power
supply replacement, it is likely because the new power supply has a mismatched airflow.
Check your console for error messages.

13.Verify that the LED on the new power supply displays steady green while the device is operating.

If the LED is not steady green, ensure that the power supply is securely installed and seated
properly.

Removal and Replacement Procedures

Brocade VDX 6940 Hardware Installation Guide

89

53-1003495-02

«
...
87
88
89
90
91
...
»

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments