Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 80

Page: 80 / 136

Non-port-side LED patterns during operation

TABLE 11

LED name

LED color

Status of hardware

Recommended action

Power supply input voltage
status:

• AC voltage for AC

power supply

• DC voltage for DC

power supply

One green LED per power
supply.

Off (no light)

Power supply is not
receiving input voltage.

Verify the assembly is on
and seated and the power
cord is connected to a
functioning power source.

Steady green

Input voltage is within
operational range.

No action required.

Power supply DC output
voltage status. One bi-
color (green and amber)
LED per power supply.

Flashing amber (1:1)

Output voltage is not
enabled.

Verify that the power
supply is fully seated and
latched in the chassis.

Flashing amber/green
(2:1)

Over temperature warning. Verify that ambient

temperature is less than
40°C (104°F) and check
for intake airflow blockage.

Flashing amber/green
(1:1)

Internal fan is out of
regulation.

Replace the power supply.

Steady amber

Power supply is faulty or
not plugged in completely.

Check the power cord,
current, voltage, and
temperature to determine
the problem.

Steady green

DC output OK.

No action required.

Fan status. One bicolor
(green and amber) LED
per fan assembly.

Off (no light)

Over temperature warning. Try the following:

• Verify the fan assembly

is seated correctly.

• Verify the device is

powered on.

Steady green

Fan assembly is operating
normally.

No action required.

Operation

Brocade VDX 6940 Hardware Installation Guide

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Search results

Summary of Contents for VDX 6940 Series

Reviews:

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 80 / 136

Search results

Summary of Contents for VDX 6940 Series

Reviews: