manualshive.com logo in svg

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 26 / 136

Share
Download
Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 26

1

Fan captive screw

2

AC plug receptacle

3

Power supply handle

4

DC output status LED

5

AC input status LED

6

Power supply airflow label

7

Locking tab

8

Integral fan air inlet

9

Fan status LED

10 Fan handle
11 Fan airflow label

FIGURE 9

 AC power supply and fan details

The following illustrations show the fan assemblies, DC power supplies, and other components on the
non-port side of the Brocade VDX 6940-144S. Refer to 

LED locations

 on page 73 for details on LED

locations.

1

Ground lug attachment screws

2

Fan #1

3

Fan #2

4

Fan #3

5

Fan #4

6

DC power supply #1

7

DC power supply #2

FIGURE 10

 Non-port-side view showing DC power supplies

The following illustration shows more detail of the fans and DC power supplies.

Device Overview

26

Brocade VDX 6940 Hardware Installation Guide

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments