manualshive.com logo in svg

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 86 / 136

Share
Download
Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 86

FIGURE 43

 Examples of airflow symbols

The green 

E

 symbol indicates an exhaust FRU. This unit pulls air in from the port side of the device

and exhausts it out the non-port side. This is called front-to-back airflow or exhaust airflow. This
symbol should appear on FRUs with part numbers ending with 

-F.

The orange 

I

 symbol indicates an intake FRU. This unit pulls air in from the non-port side of the device

and exhausts it out the port side. This is called back-to-front airflow or intake airflow. This symbol
should appear on FRUs with part numbers ending with 

-R

.

VDX 6940-36Q FRU replacement

Field-replaceable units (FRUs) include separate power supplies and fan assemblies identified through
Network OS as follows:

• Power supplies - identified from left to right as power supply #1 and power supply #2 when viewed

from the non-port-side of the device.

• Fan assemblies - identified from left to right as fan #1, fan #2, fan #3, fan #4, and fan #5 when

viewed from the non-port side of the device.

For locations of these assemblies, captive screws, LEDs, labels, and other components, refer to 

Non-

port-side views

 on page 24.

NOTE

Maintain all power supply and fan assemblies in operational condition to provide redundancy.

VDX 6940-36Q FRU replacement

86

Brocade VDX 6940 Hardware Installation Guide

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments