Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 93 | Manualshive

Page: 93 / 136

Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 93

• Check the fan status LED on the face of the fan. Refer to "Interpreting LED activity" for details on

LED normal operation and error conditions.

• Enter one of the following commands in the command line interface to display the fan status:

‐

show chassis

‐

show environment fan

Time and items required to replace a fan assembly

Replacing a fan assembly should take less than two minutes.

You need the following items to replace a fan assembly:

• A new fan assembly (must have the same part number and the same airflow label as the fan being

replaced)

• A #1 Phillips screwdriver

Replacing a fan assembly

Complete the following steps to replace a fan assembly.

1. Ensure that the replacement fan assembly has the same part number and airflow label as the fan

assembly being replaced.

2. Using the Phillips screwdriver, unscrew the captive screw on the fan assembly.
3. Remove the fan assembly from the chassis by pulling the handle on the fan assembly out and away

from the chassis.

4. Install the new fan assembly in the chassis:

a) Orient the new fan assembly with the captive screw on the right, as shown in the following

illustration.

b) With one hand, hold the bar on the front panel of the fan. With the other hand, support the

underside of the fan, and insert it into the empty fan slot. Slide the new fan into the chassis until
the latch engages.

CAUTION
Do not force the installation. If the power supply and fan assembly does not slide in easily,
ensure that it is correctly oriented before continuing.

If the device is powered up, the fan will immediately power up.

c) Using the Phillips screwdriver, secure the fan assembly to the chassis by tightening the captive

screw.

Time and items required to replace a fan assembly

Brocade VDX 6940 Hardware Installation Guide

93

53-1003495-02

«
...
91
92
93
94
95
...
»

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments