manualshive.com logo in svg

Brocade Communications Systems VDX 6940 Series, Hardware Installation Manual, Page: 35 / 136

Share
Download
Brocade Communications Systems VDX 6940 Series Hardware Installation Manual Download Page 35

1

DC wiring harness from power source

2

Wiring harness connector on power
supply

3

DC power supply

4

Locking tab

FIGURE 15

 DC power cable and power supply

2. Terminate the negative (-) and positive (+) wires at the other end of harness at DC power source and

the ground wire to building ground.
Wires in the harness are labeled and colored as follows:

DC harness wiring

TABLE 6   

Label (color)

Meaning

GND (yellow)

Earth ground (PE)

-48V (black)

Negative (-)

RTN (red)

Return positive (+)

CAUTION
For a DC system, use grounding wire of at least 8 American Wire Gauge (AWG). The
grounding wire should be attached to the DC input connector, the other end connects to the
building ground.

3. Refer to the "Power Precautions" section of this guide.
4. Observe the following additional requirements and precautions when making connections to DC

power supplies:

Device Installation

Brocade VDX 6940 Hardware Installation Guide

35

53-1003495-02

Summary of Contents for VDX 6940 Series









































































































































Reviews:

No comments